H3c-technologies H3C WX5500E Series Access Controllers Manual do Utilizador Página 49
- Página / 221
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
38
Meanwhile, the system with the higher system ID, which has identified the aggregation state changes on
the remote system, sets the aggregation state of local member ports as the same as their peer ports.
Load sharing criteria for link aggregation groups
In a link aggregation group, traffic can be load-shared across the selected member ports based on a set
of criteria, depending on your configuration.
You can choose one of the following criteria or any combination for load sharing:
• MAC addresses
• Source/Destination service port numbers
• Ingress ports
• Source/Destination IP addresses
Ethernet link aggregation configuration task list
Task Remarks
Configuring an
aggregation
group
Configuring a static aggregation group
Select either task.
Configuring a dynamic aggregation group
Configuring an
aggregate
interface
Configuring the description of an aggregate interface Optional.
Enabling link state traps for an aggregate interface Optional.
Setting the minimum number of Selected ports for an
aggregation group
Optional.
Shutting down an aggregate interface Optional.
Restoring the default settings for an aggregate interface Optional.
Configuring load sharing criteria for link aggregation groups Optional.
Configuring an aggregation group
CAUTION:
Removing an a
gg
re
g
ate interface also removes the correspondin
g
a
gg
re
g
ation
g
roup. At the same time,
all member ports leave the aggregation group.
You cannot assign a port to a Layer 2 aggregation group if any of the features listed in Table 6 is
configured on the port.
Table 6 Features incompatible with Layer 2 aggregation groups
Feature Reference
RRPP RRPP in High Availability Configuration Guide
MAC authentication
MAC authentication in Security Configuration Guide
Port security Port security in Security Configuration Guide
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Manuais e produtos relacionados com Routers H3c-technologies H3C WX5500E Series Access Controllers
(4 páginas)
(18 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais