H3c-technologies H3C SecBlade NetStream Cards Manual do Utilizador Página 236
- Página / 349
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
221
Figure 69 TFTP configuration diagram
Before using TFTP, the administrator needs to configure IP addresses for the TFTP client and server, and
make sure that there is a reachable route between the TFTP client and server.
When the device serves as the TFTP client, you need to perform the following configuration:
Table 17 Configuration when the device serves as the TFTP client
Device Confi
g
uration
Remarks
SecBlade (TFTP client)
• Configure the IP address and routing function, and
ensure that the route between the device and the TFTP
server is available.
• Use the tftp command to establish a connection to the
remote TFTP server to upload/download files to/from
the TFTP server
—
PC (TFTP server)
Enable TFTP server on the PC, and configure the TFTP
working directory.
—
Configuring the TFTP client
When a device acts as a TFTP client, you can upload a file on the device to a TFTP server and download
a file from the TFTP server to the local device. You can use either of the following methods to download
a file:
• Normal download: The device writes the obtained file to the storage medium directly. If you
download a remote file using a filename destination-filename that exists in the target directory, the
device deletes the original file and saves the new one. If file download fails due to network
disconnection or other reasons, the original file will never recover because it has been deleted.
• Secure download: The device saves the obtained file to its memory and does not write it to the
storage medium until the whole file is obtained. If you download a remote file using a filename
destination-filename that exists in the target directory, the original file is not overwritten. If file
download fails due to network disconnection or other reasons, the original file still exists. This mode
is more secure but consumes more memory.
H3C recommends you use the secure mode or, if you use the normal mode, specify a filename that does
not exist in the target directory.
- H3C SecBlade NetStream Card 1
- Preface 3
- GUI conventions 4
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- CLI configuration 16
- Entering the CLI 17
- Command conventions 17
- Undo form of a command 18
- CLI views 18
- Using the CLI online help 19
- Typing commands 20
- Typing incomplete keywords 21
- Configuring command aliases 21
- Configuring CLI hotkeys 22
- System Mana 23
- Maintenance Command Reference 23
- Checking command-line errors 24
- Using command history 24
- Controlling the CLI display 25
- Filtering output information 26
- Character Meanin 27
- Remarks 27
- Login methods 35
- Users and user interfaces 36
- Numbering user interfaces 36
- CLI login 37
- Login procedure 38
- Logging in through telnet 47
- ACSEI timers 58
- ACSEI startup and running 58
- NMS login 61
- NMS login example 63
- User login control 65
- NMS users 68
- Interface configuration 70
- General configuration 71
- IP addressing configuration 80
- Special IP addresses 81
- Subnetting and masking 81
- Configuring IP addresses 82
- 172.16.1.1/24 83
- 172.16.2.1/24 sub 83
- 172.16.1.2/24 83
- 172.16.2.2/24 83
- IP routing overview 85
- Dynamic routing protocols 86
- Routing preference 87
- Route recursion 87
- Static routing configuration 89
- Configuring a static route 90
- What is policy-based routing 93
- Configuring PBR 94
- Configuring local PBR 96
- Configuring interface PBR 96
- VLAN configuration 98
- VLAN fundamentals 99
- VLAN types 100
- Protocols and standards 100
- VLAN interface overview 101
- Configuration procedure 101
- Network requirements 102
- Verification 103
- Port link type 103
- Default VLAN 104
- To do... Use the command… 109
- Remarks 109
- Overview 110
- Working mechanism 115
- Configure the SecBlade card 119
- GE3/0/1 GE3/0/2 121
- XGE2/0/1 121
- ARP configuration 128
- Operation of ARP 129
- Configuring ARP 130
- ARP configuration example 133
- Gratuitous ARP configuration 135
- Configuring gratuitous ARP 136
- Proxy ARP configuration 137
- Local proxy ARP 138
- Enabling proxy ARP 139
- 2. Configure the SecBlade 143
- ACL configuration 144
- Match order 145
- ACL rule numbering 145
- ACL configuration task list 146
- Configuring an ACL 146
- Copying an IPv4 ACL 149
- Packet filtering with ACLs 150
- ACL configuration example 152
- NetStream overview 154
- How NetStream works 155
- Flow aging 155
- NetStream data export 156
- NetStream export formats 157
- NetStream filtering 157
- NetStream sampling 157
- IPv4 NetStream configuration 159
- Enabling IPv4 NetStream 160
- To do… Use the command… 166
- IPv6 NetStream configuration 167
- Configuration considerations 172
- Configuring the host device 173
- Configuring the NSC 175
- 1. Configure the Device 176
- Device management 188
- Configuring the system time 189
- Displaying the system time 189
- Configuring banners 192
- Rebooting the device 195
- Configuring a scheduled task 196
- NOTE: 204
- NTP configuration 205
- How NTP works 206
- NTP message format 207
- Operation modes of NTP 208
- Symmetric peers mode 209
- Broadcast mode 209
- NTP configuration task list 210
- Configuration prerequisites 213
- NTP configuration examples 214
- SecBlade and Device 217
- Automatic configuration 218
- Address acquisition process 220
- File types 221
- TFTP request sending mode 223
- FTP configuration 224
- Configuring the FTP client 225
- 10.1.1.1/16 229
- 10.3.1.1/16 229
- 10.2.1.1/16 229
- Configuring the FTP server 230
- 3. Upgrade SecBlade 233
- TFTP configuration 235
- Configuring the TFTP client 236
- File management 239
- Performing file operations 241
- Renaming a file 242
- Copying a file 242
- Moving a file 242
- Deleting a file 242
- Performing batch operations 243
- Setting prompt modes 245
- Example for file operations 246
- Configuration file overview 247
- Introduction 248
- Configuration rollback 250
- Configuration task list 250
- Device software overview 256
- Software upgrade methods 257
- Basic concepts in hotfix 258
- Patch status 259
- DEACTIVE state 260
- ACTIVE state 260
- RUNNING state 261
- One-step patch installation 262
- Loading a patch file 263
- Activating patches 263
- Confirming running patches 264
- Stopping running patches 264
- Deleting patches 264
- Network requirement 265
- Hotfix configuration example 267
- Configuring ping 268
- Tracert 269
- System debugging 270
- Information center overview 273
- System information format 277
- PRI (priority) 278
- Managing security logs files 287
- 1.1.0.1/16 1.2.0.1/16 290
- SNMP configuration 295
- SNMP configuration task list 296
- Configuring SNMPv3 297
- Configuring SNMP logging 299
- Configuring SNMP traps 299
- Enabling SNMP traps 300
- Configuring trap parameters 300
- SNMP configuration examples 302
- SNMPv3 configuration example 303
- 1.1.1.2/24 304
- XGE4/0/1XGE0/0 304
- 1.1.1.1/24 304
- MIB style configuration 307
- RMON configuration 308
- RMON groups 309
- Alarm group 310
- Private alarm group 310
- XGE4/0/1 314
Manuais e produtos relacionados com Segurança H3c-technologies H3C SecBlade NetStream Cards
(66 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais