H3c-technologies H3C SR6600-X Manual do Utilizador

H3C SR6600/SR6600-X RoutersInterface Module Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: 6PW1

2 LEDs Table 1 LED description LED status Description Off No link is present or the cable is faulty. Steady yellow A 10 Mbps link is present. Flashi

3 Front panels Figure 2 Front panel of HIM-8GBE (1) GE port (2) GE port status LED (3) Captive screw (4) Ejector lever Figure 3 Front panel of HI

4 Interface specifications Table 4 Interface specifications Item Specification Connector type RJ-45 Number of interfaces • HIM-4GBE: 4 • HIM-8GBE:

5 Front panels Figure 4 Front panel of HIM-4GBP (1) Captive screw (2) SFP port (3) SFP port status LED (4) Ejector lever Figure 5 Front panel of

6 Interface specifications Table 6 Interface specifications Item Specification Connector type SFP Number of interfaces • HIM-4GBP: 4 • HIM-8GBP: 8

7 HIM-1EXP (RT-HIM-1EXP-H3) The HIM-1EXP is a 1-port 10 GE transceiver module. It provides one 10-Gigabit Small Form-Factor Pluggable (XFP) port and

8 Item Specification Receiving sensitivity –7.5 dBm –10.3 dBm –11.3 dBm Central wavelength 850 nm 1310 nm 1550 nm Max. transmission distance 0

9 Front panels Figure 7 Front panel of HIM-CL1P (1) SFP port carrier signal LED (LINK/ACT) (2) SFP port loopback/alarm LED (LP/AL) of SFP port (3) S

10 Interface specifications Table 10 Interface specifications Item Specification Connector type SFP/LC Number of interfaces • HIM-CL1P: 1 • HIM-CL

11 • Supports three operating modes that can be configured at the CLI: CPOS E3, CPOS T3, or POS (155 M bps) . • The configuration of the operating

Copyright © 2009-2015, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmi

12 LEDs Table 11 LED description LED Status Description LINK/ACT (Green) Off No link is present. On A 155.52 Mbps link is present. Flashing The SF

13 HIM-MSP2P (RT-HIM-MSP2P-H3)/HIM-MSP4P (RT-HIM-MSP4P-H3) The HIM-MSP2P/HIM-MSP4P is a high-speed OC-3/STM-1 (155 Mbps) and OC-12/STM-4 (622 Mbps) n

14 Figure 12 Front panel (1) Captive screw (2) Ejector lever (3) SFP port carrier signal LED (LINK/ACT) (4) SFP port loopback/alarm LED (LP/AL) (5

15 Item Specification Min. –19.0 dBm –15.0 dBm –5.0 dBm –5.0 dBm Max. –14.0 dBm –8.0 dBm 0 dBm 0 dBm Receiving sensitivity –30.0 dBm –28.0

16 Front panel Figure 13 Front panel of HIM-PS1P (1) Captive screw (2) Ejector lever (3) SFP port carrier signal LED (LINK/ACT) (4) SFP port loopba

17 Item Specification Receiving sensitivity –18.0 dBm –18.0 dBm –27.0 dBm –28.0 dBm Overload optical power –3.0 dBm 0.0 dBm –9.0 dBm –8.0 dBm

18 (5) SFP port loopback/alarm LED (LP/AL) Figure 15 Front panel of HIM-AL2P (1) Captive screw (2) Ejector lever (3) SFP port (4) SFP port carrier

19 Item Specification Receiving sensitivity –30.0 dBm –28.0 dBm –34.0 dBm –34.0 dBm Overload optical power –14.0 dBm 7.0 dBm –9.0 dBm –10.0 d

20 (8) MAC external SFP port carrier signal LED (LINK/ACT) (9) MAC external SFP port loopback/alarm LED (LP/AL) (10) Mate interface of the MAC RPR n

21 Item Specification Max. transmission distance 2 km (1.24 miles) 15 km (9.32 miles) 40 km (24.86 miles) 80 km (49.71 miles) Fiber type 9/125 m si

Preface This document describes the modules (such as HIM, MIM and SAP) supported by the H3C SR6600/SR6600-X routers, the interface cables, and the com

22 LED Status Description Flashing green Data is being transmitted or received. Steady yellow A loopback exists. Flashing yellow An alarm has occu

23 Item Specification Receiving sensitivity –30.0 dBm –28.0 dBm –34.0 dBm –34.0 dBm Overload optical power –14.0 dBm –7.0 dBm –9.0 dBm –10.

24 LEDs Table 24 LED description LED Status Description SFP GE-1000Base-X LINK/ACT (Green) Off No link is present. On A 1000 Mbps link is present.

25 Item Specification Interface standards • SONET STS-3/STS-12 • SDH STM-1/STM-4 Interface speed 155.52 Mbps 622.08 Mbps OC-3 interface (155.52 Mbp

26 HIM-8GBP-V2 The HIM-8GBP-V2 interface module provides eight SFP ports. Each SFP port has a double-color LED to indicate its operating status. The

27 Item Specification Receiving sensitivity –17 dBm –20 dBm –23 dBm –21 dBm –22 dBm Central wavelength 850 nm 1310 nm 1310 nm 1550 nm 1550

28 Front panel Figure 20 Front panel (1) Captive screw (2) SFP ports (3) SFP port LEDs (4) Ejector lever LED Table 29 SFP port LED description St

29 Item Specification Central wavelength 850 nm 1310 nm 1310 nm 1550 nm 1550 nm Max. transmission distance 0.55 km (0.34 miles) 10 km (6.21 miles

30 (3) SFP+ port LED (LINK/ACT) (4) SFP+ port LEDs Table 31 SFP+ port LED description Status Description Off No link is present. Steady green A l

31 MIMs MIM-2GBE (RT-MIM-2GBE-H3) The MIM-2GBE is a 2-port 10/100/1000M Base-T copper port (RJ-45) module. The MIM-2GBE is designed for router-LAN co

Convention Description # A line that starts with a pound (#) sign is comments. GUI conventions Convention Description Boldface Window names, button

32 Item Specification 100 Mbps Full/half duplex, auto-negotiation 1000 Mbps Full duplex NOTE: • The MDI standard is typically used on the Ethe

33 Figure 24 Front panel of MIM-8E1(75)-F The front panel of MIM-8E1(75)-F is similar to that of MIM-8E1(75). LEDs Table 35 LED description LED St

34 NOTE: • The MIM-8E1(75)/MIM-8E1(75)-F does not support ISDN PRI. • For the MIM-8E1(75), if you use the timeslot binding command on the contro

35 Interface specifications Table 37 Interface specifications Item Specification Connector type RJ-45 Number of interfaces 1 Interface standard •

36 MIM-1CE3(RT-MIM-1CE3-V2-H3) The MIM-1CE3 is a 1-port channelized E3 interface module. It has the following features: • In E3 mode, it transceives

37 Interface specifications Table 40 Interface specifications Item Specification Connector type SMB Number of interfaces 2 Interface standards G. 70

38 Front panel Figure 28 Front panel (1) Carrier signal LED (LINK/ACT) (2) TX interface (3) RX interface (4) Captive screw (5) Loopback/alarm LED

39 Item Specification Services supported T3 leased line Interface cables The MIM-1CE3 provides two SMB interfaces, with one interface acting as the

40 Figure 30 Front panel of MIM-4SAE (1) Serial interface (2) Serial interface LINK LED (3) Captive screw (4) Serial interface ACT LED Figure 31

41 Interface specifications Table 45 Interface specifications Item Specification (in synchronous mode) Connector type DB-28 Number of interfaces •

Represents a security card, such as a firewall, load-balancing, NetStream, SSL VPN, IPS, or ACG card. Port numbering in examples The port numbers i

42 NOTE: • The above cables are all optional for the MIM-2SAE/MIM-4SAE/MIM-8SAE to be separately orderedif needed. • All the above cables have a

43 Item Specification Memory type and size • DDR2 SDRAM • 2 GB (default, two 1 GB memories) CAUTION: Use two DDR2 SDRAM with the same size at a ti

44 Item Specification Interface speed and duplex mode 10 Mbps Full/half duplex, auto-negotiation 100 Mbps Full/half duplex, auto-negotiation 1000 M

45 Item Specification Max power consumption • Tested—125 W • Theoretical—150 W NOTE: The theoretical max power consumption, greater than the tes

46 Item Specification Fiber type 62.5/125 m multi-mode fiber 9/125 m single-mode fiber 9/125 m single-mode fiber 9/125 m single-mode fiber 9/125

47 Front panel Figure 34 Front panel (1) SFP port (2) System status LED (RUN) (3) SFP status LED (4) Ejector lever (5) Captive screw Specification

48 LED Status Description Flashing green Data is being received or transmitted at 1000 Mbps. Steady yellow A 100 Mbps link is present. Flashing yel

49 • When working with transceiver modules supporting fiber-to-copper conversion, the SAP-48GBP uses category-5 straight-through or crossover Ethern

50 LEDs Table 56 LED description LED Status Description RUN (Green) Off No power input is available or the SAP-4EXP has failed. Slow flashing (1 Hz)

51 SAP-20GE2XP The SAP-20GE2XP provides 16 SFP ports, four combo interfaces, and two SFP+ ports. It provides a bi-color LED for each port to indicate

[Technical Support & Documents > Software Download]—Provides the documentation released with the software version. Technical support service@h3

52 LEDs Table 60 LED description LED Status Description RUN (green) Off No power input is available or the SAP-20GE2XP has failed. Slow flashing (1

53 Item Specification Network synchronization Supported 1588v2.2 protocol Supported Interface standards 802.3, 802.3u, and 802.3ab Transmit power Ty

54 Table 64 SFP+ port specifications Item Specification Connector type LC Transceiver module SFP+ Network synchronization Supported 1588v2.2 protoco

55 Interface cables Use the following cables for the SAP-20GE2XP ports: • Fiber port—An SFP/SFP+ transceiver module and a fiber that has an LC conne

56 Item Specification Combo interfaces 12. • Copper port—Straight-through/crossover autosensing: { 10/100 Mbps, half/full-duplex. { 1000 Mbps, ful

57 Interface specifications Table 69 SFP port specifications Item Specification Connector type LC Transceiver module type SFP Network synchronizatio

58 For the combo fiber port specifications, see Table 69. For the transceiver module available for the combo fiber ports, see Table 70. NOTE: Use

59 Connecting interface cables Connecting an Ethernet interface cable Appearance of an Ethernet cable Figure 38 Ethernet cable 10/100 Mbps Ethernet

60 Pinout No. A B 8 Brown Brown Table 73 Crossover cable pinouts Pinout No. A B 1 Orange/white Green/white 2 Orange Green 3 Green/white Orange/whi

61 Figure 40 SFP+ transceiver module Figure 41 XFP transceiver module Figure 42 QSFP+ transceiver module Figure 43 LC-type optical fiber connec

i Contents Interface modules ·························································································································

62 Connecting an optical fiber CAUTION: • Never stare into an open fiber Ethernet port, because invisible rays might be emitted from the port. •

63 Figure 45 8E1 splitter cable Connecting the cable When connecting the interface cable, pay attention to the mark on the interface to avoid wrong

64 Figure 46 Connecting the 4E1/8E1 splitter cable (1) { If the 75-ohm 4E1/8E1 splitter cable need be extended, you can connect the BNC connector

65 NOTE: • The Tx end of the cable must be connected to the Rx end of the peer device, and the Rx end of the cableto the Tx end of the peer devic

66 NOTE: • When connecting the interface cable, pay attention to the mark on the interface to avoid wrong insertion, which might damage the inter

67 Connecting a serial interface cable Appearance of the serial interface cable Figure 51 V.24 DTE cable Figure 52 V.24 DCE cable Figure 53 V.35

68 Figure 55 X.21 DTE cable Figure 56 X.21 DCE cable Figure 57 RS-449 DTE cable Figure 58 RS-449 DCE cable Figure 59 RS-530 DTE cable APos.

69 Figure 60 RS-530 DCE cable Connecting the cable CAUTION: • Never stare into an open fiber Ethernet port, because invisible rays might be emitt

70 Compatibility matrixes In the compatibility matrixes, "" means "Supported" and "×" means "Not supported."

71 LPU RPE-X1 RSE-X1 RSE-X2 MCP-X1 MCP-X2 FIP-210    × × FIP-240    × × FIP-300 × ×  × × FIP-310 × ×  × × FIP-600 × ×  × × SAP-4

ii Interface module&SAP and transceiver module compatibility matrix ······································································· 73Ind

72 Compatibility matrixes on Comware V7 LPU and router compatibility matrix Table 77 LPU and router compatibility matrix LPU SR6604 SR6608 SR6616 SR6

73 Interface module and FIP compatibility matrix Table 80 Interface module and FIP compatibility matrix Module FIP-10 FIP-100 FIP-110 FIP-20 FIP-200

74 Interface module&SAP 155 Mbps fiber SFP transceiver module 622 Mbps fiber SFP transceiver module 1000 Mbps fiber SFP transceiver module 100/10

75 Interface module&SAP 10/100/1000 Mbps copper SFP transceiver module 2.5 Gbps fiber SFP transceiver module 10 Gbps fiber XFP transceiver module

76 Interface module&SAP 10/100/1000 Mbps copper SFP transceiver module 2.5 Gbps fiber SFP transceiver module 10 Gbps fiber XFP transceiver module

77 Index C H I M S C Compatibility matrixes on Comware V5,70 Compatibility matrixes on Comware V7,72 Connecting a CE3/CT3 interface cable,66 Connect

1 Interface modules The SR6600/SR6600-X router supports hot swapping of interface modules. NOTE: The LPU, MPU, and router compatibility matrixes v